Geneve drive remapping

REMAP

REMAP allows a disk I/O device to be mapped to any DSK1...DSK9 device number. Usage is as follows either in an AUTOEXEC file or at the GeneveOS Command Line prompt.

REMAP <number><DRIVE>

A	Floppy #1	Any floppy-only controller
B	Floppy #2	Any floppy-only controller
C	Floppy #3	Any floppy-only controller
D	Floppy #4	Any floppy-only controller that supports 4 floppies
E	Internal Geneve Ramdisk
F	Internal Horizon Ramdisk	8 bit CRU >1400 256K
G	Internal Horizon Ramdisk	8 bit CRU >1600 256K
H	Internal Rave Ramdisk
I	HFDC Emulate File
J	HFDC Floppy #1
K	HFDC Floppy #2
L	HFDC Floppy #3
M	HFDC Floppy #4
N	Internal Horizon Ramdisk	16 bit CRU >1400
O	Internal Horizon Ramdisk	16 bit CRU >1600
P	Internal Horizon Ramdisk	16 bit CRU >1000
Q	Internal Horizon Ramdisk	16 bit CRU >1700
R	Internal Horizon Ramdisk	16 bit CRU >1800
S	Internal Horizon Ramdisk	16 bit CRU >1900
T	PFM FlashDisk #1
U	Reserved for PFM #2
V	Reserved for Future Expansion
W	TIPI DSK1	TIPI CRU >1800
X	TIPI DSK2	TIPI CRU >1800
Y	TIPI DSK3	TIPI CRU >1800
Z	TIPI DSK4	TIPI CRU >1800

Examples

REMAP 1W       Maps DSK1 to TIPI DSK1 (assumes PI.CONFIG has entry)
REMAP 4Q       Maps DSK4 to a 16 bit HRD at CRU >1700

(taken from the GeneveOS 7.30 manual)

SCSMAP

The SCSMAP command allows the use of SCS1 through SCS6 for devices.

SCSMAP also allows mapping the IDE drives to a SCS device name as

SCSMAP <x><y>

where x=1 to 6 for SCS1 to SCS6, and y=1 to 9 for SCSI connected devices 1 through 9.

To separate the IDE class of drives, the IDE drives have been set as

y=A to H where A=IDE1, B=IDE2, C=IDE3, D=IDE4, E=IDE5, F=IDE6, G=IDE7, and H=IDE8.

Please note that if you have partitioned your IDE drive to 8 partitions, our testing has indicated the 8th partition is presently not useable. We suspect this is a eprom programming issue that needs to be resolved. The IDE card needs to be running the DSR from Fred Kaal at www.ti99-geek.nl, Version 14.

The SCSMAP also allows mapping 16-bit Horizon Ramdisks into the SCSx "RamHardDrive" addressing. See identifiers below.

Please note, SCSI and IDE have more devices than the SCSMAP will presently allow. Plan drive size and mapping accordingly to maximize your equipment configuration.

Here are the default drive mappings:

SCSMAP 11	SCSI Device #1 to SCS1.
SCSMAP 22	SCSI Device #2 to SCS2.
SCSMAP 33	SCSI Device #3 to SCS3.
SCSMAP 48	HRD Ramdrive CRU >1400 to SCS4.
SCSMAP 59	HRD Ramdrive CRU >1600 to SCS5.
SCSMAP 6A	IDE 1st Drive, 1st Partition to SCS6

As an example, SCSx. may be reconfigured as follows:

SCSMAP 12	SCSI Device #2 to SCS1.
SCSMAP 26	SCSI Device #6 to SCS2.

In addition, IDE drives and the Horizon Ramdisk when configured as a RAM Harddrive are also mapped as a SCSI device as follows:

SCSMAP 48	Maps a Horizon Ramdisk at CRU >1400 to SCS4.
SCSMAP 39	Maps a Horizon Ramdisk at CRU >1600 to SCS3.
SCSMAP 37	Maps IDE Device #1 to SCS3 (special case mapping)
SCSMAP 1A	Maps IDE Device #1 to SCS1.
SCSMAP 6H	Maps IDE Device #8 (H) to SCS6.

Drive assignment	Device
0	SCSI Device ID 0
1	SCSI Device ID 1
2	SCSI Device ID 2
3	SCSI Device ID 3
4	SCSI Device ID 4
5	SCSI Device ID 5
6	SCSI Device ID 6
7	SCSI Device ID 7 (controller)
8	HRD CRU >1400 ramdisk
9	HRD CRU >1600 ramdisk
A	IDE Device #1
B	IDE Device #2
C	IDE Device #3
D	IDE Device #4
E	IDE Device #5
F	IDE Device #6
G	IDE Device #7
H	IDE Device #8

It should be noted that Drive Assignment Device "7" is also duplicated as Drive Assignment Device "A".

As of 3 April 2021, testing of the IDE support in MAME has shown a potential issue of being unable to use IDE Device #8 if a user has partitioned both drives into 4 partitions each. This is unrelated to GeneveOS as it has been confirmed in the TI-99/4A emulation as well within MAME. The developer of the DSR has been contacted for investigation.

(taken from the GeneveOS 7.30 manual)

MAME usage notes

If you want to use the WHTech SCSI controller emulation in MAME, you have to define the SCSI ID number for the hard drive. Suppose you want to assign SCSI ID 0 for the harddisk:

for the TI-99/4A (with or without EVPC):

mame ti99_4a ... -ioport:peb:slot7 whtscsi -ioport:peb:slot7:whtscsi:scsibus:0 harddisk -hard1 myscsidisk.hd

for the Geneve, Genmod, and SGCPU:

mame geneve ... -peb:slot7 whtscsi -peb:slot7:whtscsi:scsibus:0 harddisk -hard1 myscsidisk.hd

So you have to specify the kind of device that is connected to the SCSI bus at the given number (:0 for ID 0). If unspecified, nothing is connected. The SCSI controller chip is always hooked to ID 7 (even though you can select it on the real card).

When you define "harddisk" to be connected to SCSI bus IDs, the "hardX" entries are allocated one after another to these IDs in ascending order.

If you have a second card or you have a HFDC in the next slot, it will take the remaining drives. So if the SCSI card is on slot 7, uses one harddisk, and HFDC is in slot 8 with one MFM hard disk, the image "-hard1" will be linked to "SCS1", while the image "-hard2" will be "HDS1".