V9938 Video Data Processor

Officially called the MSX-Video Data Processor V9938, this video chip is one of the main advantages of the Geneve 9640. The name already suggests that this VDP is typically used in MSX computer systems.

Video modes

Mode	Description	Positions	Sprite mode	Colors	Corresponding TMS9928 mode
Text 1	Text-only mode	40x24	-	2 of 512	Text
Text 2	Text-only mode	80x25	-	4 of 512	-
Multicolor	4x4 block color graphics	64x48	1	16 of 512	Multicolor
Graphic 1	Character-oriented graphics	32x24	1	16 of 512	Graphics
Graphic 2	Character-oriented graphics, full screen	32x24	1	16 of 512	Bitmap
Graphic 3	Character-oriented graphics, full screen	32x24	2	16 of 512	-
Graphic 4	Pixel-oriented bitmap mode, 16 colors	256x192 (212)	2	16 of 512	-
Graphic 5	Pixel-oriented bitmap mode, 4 colors	512x192 (212)	2	4 of 512	-
Graphic 6	Pixel-oriented bitmap mode, 16 colors	512x192 (212)	2	16 of 512	-
Graphic 7	Pixel-oriented bitmap mode, 256 colors	256x192 (212)	2	256	-

Commands

Benchmarks

I wrote a couple of benchmark programs that run in native mode and use the clock chip for measuring the command execution times. The commands are repeated many thousand times so that in the end, an execution time in the range of several seconds up to minutes is measured; dividing by the iteration count and considering setup times, we get a good estimation of the single execution time.

This information is particularly important when using the VDP commands in time-critical situations, for instance, in games.

The times for the line operation vary, depending on the angle. Horizontal and vertical lines are fastest, while 45° diagonal lines are slowest. (This is a bit surprising, since on a raster screen, a line always consists of max(dx,dy) pixels.)

Tests showed that painting a rectangle is faster when there are fewer lines: 30 pixels wide, 60 pixels high is slower than 60 wide and 30 high (about 166 µs).

Graphic 7 mode

Command	Description	Specifics	Setup [µs]	µs per pixel	Pixels per sec
HMMC	Write bytes into rectangle	Fast	133	39	25640
LMMC	Write bytes into rectangle	Logical	133	39	25640
HMMV	Fill rectangle with one color	Fast	37	2.9	344828
LMMV	Fill rectangle with one color	Logical	37	6.1	163934
HMMM	Copy rectangle content	Fast	100	5.875	170213
YMMM	Copy rectangle content, Y only	Very fast	100	5.125	195122
LMMM	Copy rectangle content	Logical	100	8.375	119403
LINE	Draw line	Logical	56	6.2..8.2	121951..161290

The setup time is a fixed time, independent of the amount of modified pixels on the screen. Maybe it is caused by internal calculations of the VDP, or by some trailing delay. You have to add some more time for your program to set the video registers; this is typically another 100 µs.

Graphic 6 mode

The high-speed operations like HMMV perform at double speed. The reason is that two pixels are processed in a single command invocation. Logical operations only operate on single pixels and thus run at the same speed as in graphic 7.

Examples:

The following calculations all refer to graphic 7 mode, and we leave away all setup times. Thus, the required times are lower bounds; it will take longer to perform the action. Also, we assume 192 lines; the V9938 is able to expand this to 212 lines.

• We'd like to paint the whole screen: There are 192 rows and 256 columns, which means 49152 pixels. Using the HMMV command, we see that this takes t = 2.9 µs * 49152 = 142541 µs = 0.14 secs. Doing that repeatedly, we will achieve less than 8 frames per second.

• Instead of filling a rectangle, we can draw lines in subsequent rows. If we want to fill the screen, we have 192 lines with a length of 256 pixels. Each line takes about 1587 µs, hence, it takes 0.3 secs to fill the screen. (Exactly 0.343 secs, as a sample program proved.)

• Suppose we want to shift the upper half of the screen down by one row. The upper half takes up 24576 pixels; moving the contents with the fastest YMMM command takes 125952 µs = 0.126 secs, again, just 8 frames per second.

• We'd like to print a text on the graphics screen. Each character consists of 8x8 = 64 pixels. Using the HMMC command, printing a single character takes about 2500 µs, so we get 400 characters/second. Since 768 characters fit on the screen, it takes almost 2 seconds to fill the screen with characters.

• Alternatively, we could store the glyphs of the characters in a non-visible screen area, again, as 8x8 pixels rectangles and then just copy the glyph to the desired screen position. This can be done with the HMMM command. One character takes 376 µs, this means 2660 characters per second.

If we think about serious game programming, 8 frames per second is pretty disappointing. The line command is certainly useful, and also painting into the rectangles, but mass transfer should be avoided.