Geneve physical memory map

The physical memory map declares which physical addresses are used to access memory regions or devices.

Native mode

Memory map

Address	Banks	Region
000000	00-3F	512 KiB On-board DRAM	Slow RAM (1 ws)
080000	40-7F	512 KiB On-board DRAM expansion	Allocated, but technically infeasible (no sockets or signal lines)
100000	80-B7	448 KiB P-Box space	May be used my MEMEX card
170000	B8-BF	64 KiB P-Box space	Used by current expansion cards
180000	C0-E7	Future expansion	SRAM expansion in the P-Box
1D0000	E8-EB	32 KiB On-board SRAM expansion	Soldered on top of the existing 32 KiB chip
1D8000	EC-EF	32 KiB On-board SRAM	Original SRAM memory (0 ws)
1E0000	F0-FF	128 KiB Boot EPROM	Originally, only 16 KiB installed at F0,F1; mirrored

Boot EPROM space

The Boot EPROM region may have up to 128 KiB space as 16 banks of 8 KiB. This is used with the PFM.

On reset, bank F8 is mapped into the 0000-1FFF logical address region. The EPROM on the stock Geneve defines all even banks as mirrors of F0, and all odd banks as mirrors of F1.

GPL mode

Memory map

Address	Banks	Region
000000	00-35	432 KiB On-board DRAM	Slow RAM (1 ws)
06C000	36	8 KiB Cartridge ROM space (bank 1)	First bank of cartridge (Extended Basic style)
06E000	37	8 KiB Cartridge ROM space (bank 2)	Second bank of cartridge (Extended Basic style)
070000	38-3F	64 KiB GRAM Cartridge space	Mapper byte 06 must be set to 0x03 to enable GROM/GRAM
080000	40-7F	512 KiB On-board DRAM expansion	Allocated, but technically infeasible (no sockets or signal lines)
100000	80-B7	448 KiB P-Box space	May be used by MEMEX card
170000	B8-BF	64 KiB P-Box space	Used by current expansion cards
180000	C0-E7	Future expansion	SRAM expansion in the P-Box
1D0000	E8-EB	32 KiB On-board SRAM expansion	Soldered on top of the existing 32 KiB chip
1D8000	EC-EF	32 KiB On-board SRAM	Original SRAM memory (0 ws)
1E0000	F0-FF	128 KiB Boot EPROM	Originally, only 16 KiB installed at F0,F1; mirrored

Cartridge emulation

The cartridge emulation in the Gate array shows some peculiarities.

• The mapper byte 06 (F116 / 8006) must be set to 03 to enable the GROM/GRAM cartridge space. Otherwise, no GROM/GRAM handling is emulated.
• In GPL mode, logical addresses 6000-7FFF are always mapped to bank 36/37, regardless of the mapper byte 03 (F113 / 8003).
• CRU address 1EF8 is used to switch between single or dual bank cartridge ROM. When set to 0, only bank 36 is used. When set to 1, writing to cartridge space addresses 6000 + n*4 selects bank 36, while writing to 6002 + n*4 selects bank 37.
• Cartridge GRAM regions are 8 KiB large, unlike real GROMs with 6 KiB.
• Address wrapping occurs at 8K boundaries (3FFF+1 = 2000).
• Reading via the GROM read address delivers the byte at the current GROM address, then advances the address by 1. Writing puts the byte at the current address, then advances the address by 1.
• Reading the GROM address pointer delivers the MSB, then on every subsequent read access the LSB. The counter contains the former LSB in both bytes after reading and must be restored.

Genmod

The Genmod (Geneve modification) can be run in two modes, selectable by a switch. The TI mode activates the on-board slow DRAM, which is required to run the GPL mode. The reason is that the Gate array maps the GROM accesses to the DRAM on the board, which cannot be changed to the external RAM.

TI mode

Address	Banks	Region
000000	00-35	432 KiB On-board DRAM	Slow RAM (1 ws)
06C000	36	8 KiB Cartridge ROM space (bank 1)	First bank of cartridge (Extended Basic style)
06E000	37	8 KiB Cartridge ROM space (bank 2)	Second bank of cartridge (Extended Basic style)
070000	38-3F	64 KiB GRAM Cartridge space	Map byte 06 must be set to 0x03 to enable GRAM
080000	40-EF	1408 KiB P-Box memory expansion (MEMEX)	SRAM (0 ws)
1E0000	F0-FF	128 KiB Boot EPROM	Originally, only 16 KiB installed at F0,F1; mirrored

Non-TI mode

Address	Banks	Region
000000	00-EF	1920 P-Box memory expansion (MEMEX)	SRAM (0 ws)
1E0000	F0-FF	128 KiB Boot EPROM	Originally, only 16 KiB installed at F0,F1; mirrored